Clik here to view.
HATs and other add-ons • Re: Seeking Hat for Extending USB Interface Without...
Thank you for your response. The model I’m using is a Pi4, which was mentioned in the subject. However, from my understanding, a basic USB HAT for the Pi4 should also work with the Pi5.To clarify...
View ArticleHATs and other add-ons • Using Fanshim and SIM7600x Hat together
I'm trying to send SMS using the SIM7600X on my Raspberry Pi 3B+, but I also have a Fan SHIM installed. The problem is that both the SIM7600X and the Fan SHIM's LEDs are using the same UART pins (GPIO...
View ArticleHATs and other add-ons • Re: Using Fanshim and SIM7600x Hat together
is the schematics of the fanshim open source? You may better ask in pimoroni forum.If both add-on boards require the same GPIO - i.e. the Pi's UART - you can't stack them.Statistics: Posted by...
View ArticleHATs and other add-ons • Re: Cariboulite sdr hat
https://github.com/cariboulabs/cariboul ... -for-rpi-5Statistics: Posted by redvli — Fri Sep 13, 2024 11:25 am
View ArticleHATs and other add-ons • Re: Raspberry Pi 5 with Flirc - Idle Temperature?
I hope there are people here who have the Flirc for RPi5,and can write the Idle Temperature they're getting..Statistics: Posted by spaceman5 — Fri Sep 13, 2024 1:18 pm
View ArticleHATs and other add-ons • Set raspberry pi 5 fan in 0-100 range
Hello everyone,I want to make a small controller-like UI for my pi's fan so I can change the speed and make it silent when it's screaming for no reason. I know I can set the speed in the 1-4 range...
View ArticleHATs and other add-ons • Re: Set raspberry pi 5 fan in 0-100 range
You can integrate your own fan curve. Lots of discusssions on that aroud the forum. Fan is controlled via hwmon as as pwm-fan compatile. Duty cycle for that is 0 to 255. So your GUI will have to...
View ArticleHATs and other add-ons • Logic level shifter recommendations
I am attempting to interface an Echo mic board to a Pi and have an issue with the logic levels.The board uses 4 x tlv320adc3101 for the microphones and they use the following voltages:AVDD (Analog...
View ArticleHATs and other add-ons • WM8960 Audio Issues
Hello all, I recently purchased a WM8960 hat for a hobby project, I simply just want to play an audio file (.wav or .mp3) decently loudly through a speaker. It is mounted onto a Raspberry Pi 3B+ with...
View ArticleHATs and other add-ons • Rpi5 + M.2 HAT+, any compatible cases or active coolers
Hi all,the question is all in the subject. I'd love to wrap Rpi5 and M.2 HAT+ in a real case (e.g. Sunfounder's Pironman 5) but I wonder about discovering incompatibilities after purchasing all the...
View ArticleHATs and other add-ons • ADC compatibility & functioning
I am an absolute beginner and planning to purchase an RPI hat which is a 4 channel ADC. (Product link> https://wiki.seeedstudio.com/4-Channel_ ... i-ADS1115/ ). I have three sensors (pressure) each...
View ArticleHATs and other add-ons • Re: Rpi5 + M.2 HAT+, any compatible cases or active...
viewtopic.php?p=2233478&hilit=KKSB#p2233478Used KKSB case but can't recommend because of the bad thermal design.If you're using your Pi under normal load the case might be o.k.Statistics: Posted...
View ArticleHATs and other add-ons • Re: ADC compatibility & functioning
Hi raccoon396, 1. Yes it is fine be sure that you connect all the 0V to gnd. You will need an terminal block because you will have three 0V wires from your sensor and the 3 resistors which will...
View ArticleHATs and other add-ons • HAT for Pico <=> Pi5 connectivity?
Greetings and apologies if this has been covered elsewhere.I'm interested in using the Pico(2) programmable IO system as a serial standard converter. The idea being to have a Pi connected via SPI to a...
View ArticleHATs and other add-ons • Re: Logic level shifter recommendations
Apologies if I must missed something obvious. Is there a link to the board or (better) a schematic? Bit hard to tell otherwise.Statistics: Posted by g40 — Mon Sep 16, 2024 5:51 pm
View ArticleHATs and other add-ons • Re: Do you have any experience with eink \ epaper...
What did I miss? A starter for 10, complete with reviews: https://thepihut.com/collections/epaper ... spberry-piStatistics: Posted by g40 — Mon Sep 16, 2024 6:40 pm
View ArticleHATs and other add-ons • Re: In-box heatsink removal?
If there is a heatsink fixed to yoir Pi it's not new! A fresh out of the box Pi has no heatsinks mounted!Statistics: Posted by aBUGSworstnightmare — Tue Sep 17, 2024 8:21 pm
View ArticleHATs and other add-ons • Re: In-box heatsink removal? [Solved]
A light twisting ~15deg clockwise, then the same CCW and the little blighter came off without any trouble. No trace of adhesive residue either.Thanks again.Statistics: Posted by g40 — Tue Sep 17, 2024...
View ArticleHATs and other add-ons • M.2 and POE HATs: Preferred stacking order?
Thoughts/advice sought please.The board is an 8GB Pi5 with an official active cooler. I suspect I'd like to keep this in situ.Case not a consideration/constraint here. The aim is to assemble a POE...
View ArticleHATs and other add-ons • Re: M.2 and POE HATs: Preferred stacking order?
How do you want to mount that POE HAT with an active cooler installed?The FPC of the official HAT will limit the stacking height. There os no longer FPC available.Have you checked with Waveshare if...
View Article