HATs and other add-ons • Using PoE+ HAT and requesting additional power from...
I haven't seen mention of it or can't find it, but is there a sample script, documentation or something about how to request the additional power from the switch when using the PoE+ Hat.Statistics:...
View ArticleHATs and other add-ons • Re: Using PoE+ HAT and requesting additional power...
No. It will always request 25Watts from the switch. If the switch isn't PoE+ then you will get the lower power. If you exceed the power draw then the switch may shut you down.Statistics: Posted by...
View ArticleHATs and other add-ons • Re: NVMe over PCIe causing problems
@Racker_CRO I'm seeing an almost identical issue to what you have. My RPi5 W/NVMe works great outside the case but, put it in the case and if fails (usually during, or minutes after, boot). My H/W:...
View ArticleClik here to view.
HATs and other add-ons • official raspberry pi power supply not working with...
Hi all,sorry if this is not the right place to post this question but I did not find anything closer in the hardware section.I have bought a raspberry pi 5 official power supply and it works fine with...
View ArticleHATs and other add-ons • Re: official raspberry pi power supply not working...
Your third party CM4 carrier boards have out of spec USB-C ports. They've got missing or incorrect CC pulldown resistors. The Pi 5 PSU is checking for that pulldown before enabling the output. The...
View ArticleHATs and other add-ons • Wifi 6e/7 6GHz USB adapters that work with the Pi 5?
Does anyone know of Wifi 6e/7 USB adapters that work with the Pi 5?I'm specifically looking to use the 6GHz frequency instead of 2.4 or 5.Thanks.Statistics: Posted by EvilMonkeySlayer — Fri Nov 22,...
View ArticleHATs and other add-ons • Re: Wifi 6e/7 6GHz USB adapters that work with the...
maybe https://github.com/morrownr/USB-WiFi/bl ... drivers.md gives you some ideaStatistics: Posted by aBUGSworstnightmare — Fri Nov 22, 2024 11:17 am
View ArticleHATs and other add-ons • Raspberry Pi "official" USB SDXC adapter...
Hi allNow that "official" RPi SDXC cards and USB adapters have become available, I ordered a 128GB card and one of these adapters (those with two USB plugs) together with a RPI 5 (8GB RAM) to try...
View ArticleHATs and other add-ons • Re: Raspberry Pi "official" USB SDXC...
Yes, there are official cards but I was not aware of official usb readers, maybe there is no such thing, can you send a link to one?Statistics: Posted by fanoush — Sat Nov 23, 2024 9:56 am
View ArticleHATs and other add-ons • I would like to back up all of my 3.1/2-in floppy...
I know I can do this with a PC and some hardware but I'd rather dedicate a raspberry pi to the project. I have a bunch of old floppy disks 3.5-in and 5.25 in discs dead like to put in an enclosure...
View ArticleHATs and other add-ons • Re: I would like to back up all of my 3.1/2-in...
There is a very good article here https://www.raspberrypi.com/news/read-f ... gpimonday/Statistics: Posted by aBUGSworstnightmare — Sun Nov 24, 2024 7:14 pm
View ArticleHATs and other add-ons • Hardware Help
I have a RPi Active Cooler sandwiched between my RPi5 and my M.2 HAT - all screwed together using standoffs and long screws. But the GPIO pins are no longer exposed nor is there any way I can see to...
View ArticleHATs and other add-ons • Re: Hardware Help
I have a RPi Active Cooler sandwiched between my RPi5 and my M.2 HAT - all screwed together using standoffs and long screws. But the GPIO pins are no longer exposed nor is there any way I can see to...
View ArticleHATs and other add-ons • Re: Error: no module named pa1010d (The Pi Hut GPS...
I apologise for the 10 day delay in responding but other domestic tasks got in the way!To be honest I was a bit overwhelmed (baffled) by the responses but there was a valid article in the latest MagPi...
View ArticleHATs and other add-ons • RPi 3B+ V1.4 PMIC Problem
Hello everybodyI reach out to you to first to understand and afterwards to solve the following problem:We have a hat designed for RPi 3B/3B+ that provides 5v power via GIPO 2 & 4 and GND on GPIO 6...
View ArticleHATs and other add-ons • SATA HAT with USB3 hub works on USB2 port but not...
I set up a RPi4B with SATA quad hat (https://wiki.radxa.com/Dual_Quad_SATA_HAT) for home lab solution. Work fine with the bridge connector (2x USB3 from HAT to the 2x USB3 of the RPi4B). Running...
View ArticleHATs and other add-ons • Re: NVMe overheating issues with GeekWorm dual NVMe hat
Just a little update on this (probably final). It could help someone.I've found out that adding the dtparam=pciex1_gen=3 parameter in cmdline (which enables pci express gen 3) made the issue appear...
View ArticleHATs and other add-ons • Re: SATA HAT with USB3 hub works on USB2 port but...
in talking with someone, we had an epiphany: it has probably to do with the wiring of the USB-A to USB-A cable itself... The Pin to Pin connection is crossed over for the SuperSpeed Data Pair. found...
View ArticleHATs and other add-ons • KVM over IP Add-on for Raspberry Pi 5
I have a spare Raspberry Pi 5 that I want to use as a KVM over IP especially because of the inbuilt wi-fi. A cursory search indicates to the Geekworm KVM-A4 V2.0 Kit for Raspberry Pi Zero. Would this...
View ArticleHATs and other add-ons • Re: KVM over IP Add-on for Raspberry Pi 5
Potentially, but it depends on their software.It's using the Toshiba HDMI to CSI2 bridge chip, and the handling of CSI2 has changed significantly with Pi5. It's possible, but requires software...
View Article