HATs and other add-ons • Re: Gertbot Vendors or PCB order?
Everywhere I looked says that the board is discontinued. So it looks like you're out of luck.Statistics: Posted by DougieLawson — Tue May 14, 2024 3:48 pm
View ArticleClik here to view.
HATs and other add-ons • DAC Pro RCA component code?
Does anyone know the manufacturer & part number of the RCA connector on the DAC Pro SC0369?I found some older IQaudio documentation that mentions some part numbers, but it does not include any...
View ArticleHATs and other add-ons • Pi5, nvme adaptors, and gpio pin availability
I haven’t seen anyone ask about this, so I will stumble ahead and ask the ignorant questions … There seem to be a lot of differences in how nvme m.2 adaptor boards use or attach to or just block the...
View ArticleClik here to view.
HATs and other add-ons • Re: Pi5, nvme adaptors, and gpio pin availability
If you look at https://www.raspberrypi.com/products/m2-hat-plus/ there is a schematic, can't you work out used gpios from that ?It doesn't look like they use much more than power, ground , ID_SD and...
View ArticleHATs and other add-ons • kicad model for raspberry pi gpio header; pi side
Hi,There's a HAT/case for the raspberry pi called the PiDP11 (https://obsolescence.wixsite.com/obsolescence/pidp-11 ).In it, you connect a regular raspberry pi 3, 4 or 5.Now I would like to replace...
View ArticleHATs and other add-ons • Re: kicad model for raspberry pi gpio header; pi side
According to the following thread, "The Raspberry Pi B+ GPIO header is a standard 2x20 pin straight header.The footprint for that part is the "Pin_Header_Straight_2x20" footprint in the "Pin_Headers"...
View ArticleHATs and other add-ons • Re: Active Cooling Fan Not Spinning
I will take a look and see. I don't recall any issues inserting it.Statistics: Posted by ironfruit — Thu May 16, 2024 12:17 am
View ArticleClik here to view.
HATs and other add-ons • Re: New M.2 NVMe HAT+ in Official Pi 5 case
Pictures added - what is also quite funny is the M.2 HAT+ photo on the Raspberry Pi.com front page website also has this fault. Statistics: Posted by AndrewPiEater — Thu May 16, 2024 12:55 pm
View ArticleHATs and other add-ons • Why is there no M.2 HAT+ overlay?
Where to find the M.2 overlay? What data is in the EEPROM?As the HAT just uses power from the Pi it should be possible to use it connected via i.e. Jumper wires (power supply) instead of mounting it...
View ArticleHATs and other add-ons • Re: Why is there no M.2 HAT+ overlay?
The only config I've seen is to do with the pcie interface. For example:dtparam=pciex1_gen=3PeterOStatistics: Posted by PeterO — Thu May 16, 2024 5:50 pm
View ArticleHATs and other add-ons • SSD compatibility with M.2 HAT+
What experience has everyone had with SSD drivers and the new Raspberry Pi M.2 HAT+I have tried three different SSDs and none have worked so far with the official HAT, although one does work with a...
View ArticleHATs and other add-ons • Re: SSD compatibility with M.2 HAT+
One is a Transcend M.2 SSD 420S - does not work with Pimoroni or RPiFrom a quick look around, that 420S has a SATA interface, not NVME PCIe as required. So it won't work with the PCIe interface. You...
View ArticleHATs and other add-ons • Power & data over USB ports?
I have a possible project to interface a Pi Zero or other Pi device to a Contour shuttle pro USB controller via a USB port that passes power and serial data interface to the controller on the input...
View ArticleHATs and other add-ons • Re: Power & data over USB ports?
Sorry, I don't get that.The Pi Zero has two microUSB sockets: one is power only, the other one is a standard USB (Power+Data).From what I get from your description is that the Pi should act as a...
View ArticleHATs and other add-ons • pi5 fan controll
Is there a way to adjust or control the raspberry Pi 5 active cooler? I understand it is controlled by pulse width modulation.Statistics: Posted by imsdal70 — Sun May 19, 2024 5:02 am
View ArticleHATs and other add-ons • Re: pi5 fan controll
There are quite some posts here on the forum on that topic. A forum search might be helpful.From https://github.com/raspberrypi/linux/bl ... EADME#L265Code: fan_temp0 Temperature threshold (in...
View ArticleHATs and other add-ons • Re: Heatsink for 2230 SSD and Raspberry Pi M.2 HAT+...
What lets you assume the NVMe will run that hot?You can i.e. buy a 2280 heatsink and then cut it to the required size (if you think you'll need a heatsink).Or buy i.e. One fom amazon (search for 2230...
View ArticleHATs and other add-ons • Re: New M.2 NVMe HAT+ in Official Pi 5 case
The M.2 HAT will fit in the official case (although it was not designed to do so), but you need to remove the fan plate and if you want to, add an active cooler. You won't be able to fit the final top...
View ArticleHATs and other add-ons • Power efficient nvme ssd for the Argon NEO 5 M.2...
Hi, any recommendation for a power efficient and cheap 500Gb nvme ssd for the Argon NEO 5 M.2 NVME Pi5?Also, I'm using an external usb3 4tb HDD for media.Do you think can I upgrade and boot from the...
View ArticleHATs and other add-ons • Re: PI5 with m.2 hat (Geekworm X1003) doesnt work...
Thanks a lot, I am interested in your results. I bought the X1003 because it is the only one i know that fits in the official case.Statistics: Posted by Emperor — Sun May 19, 2024 9:49 pm
View Article