HATs and other add-ons • Re: Help with raspberry zero wh
Hi,I tried connecting the various SPI display pins but it turns on and stays white.Can anyone tell me how exactly connect the individual pins of an ili9341 on the picade x hat? ThanksStatistics:...
View ArticleHATs and other add-ons • Compatible case for RPI5 with M.2 Hat
Hi,I want to buy a raspberry pi 5 with this bundle : google coral tpu + m.2 hat. https://pineberrypi.com/products/hat-ai ... berry-pi-5Does anyone know a compatible case ? I found many cases, but...
View ArticleHATs and other add-ons • Re: Compatible case for RPI5 with M.2 Hat
This case looks like it supports a bottom mounted shield like the one you bought:https://geekworm.com/collections/raspbe ... ducts/p580-benStatistics: Posted by dcbenji — Tue Apr 16, 2024 9:15 pm
View ArticleHATs and other add-ons • Argon NEO 5 M.2 NVME PCIE Case
Hi,i purchased the Argon NEO 5 M.2 NVME PCIE Case for my raspberry Pi5 and i am using this NVMe SSD: https://www.amazon.de/Crucial-Plus-PCIe ... B0BYW8FLKNMy benchmark is showing:disk read: 750 MB/sec...
View ArticleHATs and other add-ons • Identify which barcode scanner
Hello,It is decided to use Raspberry Pi 4. There will be multiple barcode scanners connected.It is possible to have 3-4 barcode readers for different operations. Assuming only in/out setup that would...
View ArticleHATs and other add-ons • Re: Identify which barcode scanner
Have you chosen the model of barcode scanner? If so, have you checked the manual to see if you can specify a prefix which can identify an individual scanner?Statistics: Posted by ame — Tue Apr 16,...
View ArticleClik here to view.
HATs and other add-ons • Weird issue with ch341-uart converter on Pi 5 only
I use a ESP32-devboard that sends some sensor data to a Pi over serial, using the dev board built in ch341-uart converter. This has been working fine on Pi4's since a long time, but now I'm seeing...
View ArticleHATs and other add-ons • OpenCM 9.04 or Poppy Pixl Board - to control XL320
Hello everyone,I want to control 5x Dynamixel XL-320 motors for a project (must be these motors due to the design and properties etc.).The basis should be an RPi3B, RPi3B+ or RPi4, depending on the...
View ArticleHATs and other add-ons • Re: Argon NEO 5 M.2 NVME PCIE Case
Hi,i purchased the Argon NEO 5 M.2 NVME PCIE Case for my raspberry Pi5 and i am using this NVMe SSD: https://www.amazon.de/Crucial-Plus-PCIe ... B0BYW8FLKNMy benchmark is showing:disk read: 750 MB/sec...
View ArticleHATs and other add-ons • OpenCM 9.04 or Poppy Pixl Board - to control XL320...
Hello everyone,I want to control 5x Dynamixel XL-320 motors for a project i started (it have to be these motors, due to the design and properties etc.).The basis should be an RPi3B, RPi3B+ or RPi4,...
View ArticleHATs and other add-ons • Connect multiple SATA HDD's to Pi5
Hey there,the plan for my build is to connect multiple 3.5" HDD's to my Pi, ideally with a low energy consumption.My first attempts use external USB enclosures that come with their own power...
View ArticleHATs and other add-ons • Re: high cpu with 2-CH RS485 HAT Interface-Card and pi5
The problem was caused by the sc16is75x overlays not preparing the interrupt pin correctly, and should be fixed by this Pull Request: https://github.com/raspberrypi/linux/pull/6111In about 45 minutes...
View ArticleHATs and other add-ons • Re: Connect multiple SATA HDD's to Pi5
Maybe with an NVME hat + an NVME to 6 SATA adapter?That's one way but be careful with the M.2 adapter. A fully populated M.2 M key slot has both four PCIe lanes and a SATA port present. AFAIK all the...
View ArticleHATs and other add-ons • Audio & USB HATs allowing access to header for IO
I have a project I have earmarked for a RaspberryPi, and I hope you can advise.I could not find the information on a supplier's website to allow me to resolve this question, hence I am asking for your...
View ArticleHATs and other add-ons • Re: Audio & USB HATs allowing access to header...
I am looking to have a Pi, with a UPS HAT and an audio HATHave you mapped the GPIO pins each HAT uses to make sure you don't have any conflicts?Statistics: Posted by DS256 — Thu Apr 18, 2024 4:35 pm
View ArticleHATs and other add-ons • waveshare HAT+ plus nvme m.2 issue
My current issue is that i have connected the nvme drive (acpi M2PD3-4L 256GB) properly with the HAT+ , the pi OS seems to be able to see the drive:vaios@pi5:~ $ lsblkNAME MAJ:MIN RM SIZE RO TYPE...
View ArticleClik here to view.
HATs and other add-ons • Re: Run script requiring network before shutdown or...
Hey I'm failing to make this work. I don't have a wireguard service running, so I assume it' enough to have something like this:Code: [Unit]Description=Log Shutdown to...
View ArticleHATs and other add-ons • Re: waveshare HAT+ plus nvme m.2 issue
Pimoroni has a list of drives working on THEIR product https://shop.pimoroni.com/products/nvme ... 9587178579Ask waveshare support to provide information which drives have been tested and were...
View ArticleHATs and other add-ons • GPIO hat breakout pins?
First, my apologies for not knowing exactly what im talking about, so a little help with the nomenclature may be needed...A few years back I built a streamer, Believe its the Rpie4, have the 7" touch...
View ArticleHATs and other add-ons • Re: GPIO hat breakout pins?
Using two power supplies --- one for the screen and one for the Pi -- worked for me (actually I used a non-Raspberry dual USB supply, each channel having an adequate current rating, but it was an...
View Article